Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
builderpages:plasmo:cmp68k_mpu302 [2017/08/17 20:25] plasmo |
builderpages:plasmo:cmp68k_mpu302 [2017/12/08 17:06] (current) plasmo |
||
---|---|---|---|
Line 1: | Line 1: | ||
- | **[[https:// | + | **[[https:// |
+ | |||
+ | <font inherit/ | ||
+ | | ||
+ | |||
+ | ===== ===== | ||
===== Guide for operating CP/M68K v1.3 on MPU302 ===== | ===== Guide for operating CP/M68K v1.3 on MPU302 ===== | ||
Line 7: | Line 12: | ||
<font 16px/ | <font 16px/ | ||
- | Powering the board requires a 25-pin null modem between the CRAFT connector and a PC. Set baud rate to 38400, 8N1, no hardware handshake. | + | Powering the board requires a 25-pin null modem between the CRAFT connector and a PC. Set baud rate to 38400, 8N1, RTS/ |
Hook up 5V & ground to the points indicated by the arrows. The ' | Hook up 5V & ground to the points indicated by the arrows. The ' | ||
- | [[https:// | + | [[https:// |
Immediately at power on, this message (**bold**) will be displayed: | Immediately at power on, this message (**bold**) will be displayed: | ||
Line 35: | Line 40: | ||
* Drive C resides on super-capacitor-backed RAM. It is read/ | * Drive C resides on super-capacitor-backed RAM. It is read/ | ||
- | Content of Drive A: <–This is updated on 8/17/17, previous content can be found [[: | + | Content of Drive A: <- This is updated on 8/17/17, previous content can be found [[: |
- | <font inherit/ | + | A: CPM REL : SD REL : CPM SYS : DDT68000 68K : README TXT \\ |
A: CB68 68K : AS68INIT : CLIB : CLINK SUB : CLINKE SUB \\ | A: CB68 68K : AS68INIT : CLIB : CLINK SUB : CLINKE SUB \\ | ||
A: CLINKF SUB : LIBE A : LIBF A : S O : ASSERT H \\ | A: CLINKF SUB : LIBE A : LIBF A : S O : ASSERT H \\ | ||
Line 56: | Line 61: | ||
A: MORE 68K : NM68 68K : C068 68K : C168 68K : LINK68 68K \\ | A: MORE 68K : NM68 68K : C068 68K : C168 68K : LINK68 68K \\ | ||
A: SENDC68 68K : SIZE68 68K : XFER86 68K : FORMAT 68K : TERM 68K \\ | A: SENDC68 68K : SIZE68 68K : XFER86 68K : FORMAT 68K : TERM 68K \\ | ||
- | A: CONFIG 68K : PUTBOOT 68K : AS68SYMB DAT : CONC SUB</ | + | A: CONFIG 68K : PUTBOOT 68K : AS68SYMB DAT : CONC SUB |
- | Content of Drive B: <-- With updated drive A of 8/17/17, drive B can be used for other data | + | Content of Drive B: <- With updated drive A of 8/17/17, drive B can be used for other data |
- | <font inherit/ | + | B: CB68 68K : CB68 L68 : CB68 DOC : SHORT BAS : ASCIIART BAS \\ |
- | B: SRIN1 S : SRIN S</ | + | B: SRIN1 S : SRIN S |
<font 16px/ | <font 16px/ | ||
Line 67: | Line 72: | ||
The board contains two AMbug monitors. The primary one resides on a pair of 29F010 flash, UB2, UB3. The backup monitor reside on the first sector (128K byte sector) of UD3, UE3. If the primary monitor is corrupted, the backup monitor can be activated by unsoldering and swapping two existing jumper wires as shown below. (A procedure on how to reprogram the primary AMbug will be written…) | The board contains two AMbug monitors. The primary one resides on a pair of 29F010 flash, UB2, UB3. The backup monitor reside on the first sector (128K byte sector) of UD3, UE3. If the primary monitor is corrupted, the backup monitor can be activated by unsoldering and swapping two existing jumper wires as shown below. (A procedure on how to reprogram the primary AMbug will be written…) | ||
- | [[https:// | + | [[https:// |
<font 16px/ | <font 16px/ | ||
Line 79: | Line 84: | ||
Data and programs requires to load CPM v1.3 distribution files into drive A: | Data and programs requires to load CPM v1.3 distribution files into drive A: | ||
- | * Part 1 of {{: | + | * Part 1 of {{: |
- | * Part 2 of {{: | + | * Part 2 of {{: |
Data and program required to load BASIC executable and BASIC library into drive B: | Data and program required to load BASIC executable and BASIC library into drive B: |