Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
builderpages:plasmo:z280rc:new_cfdisk [2018/06/09 23:46]
plasmo
builderpages:plasmo:z280rc:new_cfdisk [2018/06/10 13:13] (current)
plasmo
Line 7: Line 7:
  
 **Enable the UART Bootstrap mode by removing the Mode jumper.\\ **Enable the UART Bootstrap mode by removing the Mode jumper.\\
-Upload ​'​loadngo.run'​ as binary file: <- Please note: it may be necessary to add 1ms transmission delay to every line**+Send '{{:​builderpages:​plasmo:​z280rc:​loadngo.zip|loadngo.run}} ' as binary file: <- Please note: it may be necessary to add 1ms transmission delay to every line**
  
 //​……………………………………………………………………………………………………………………………………………UX\\ //​……………………………………………………………………………………………………………………………………………UX\\
Line 37: Line 37:
 ===== Load files in CF Bootstrap mode ===== ===== Load files in CF Bootstrap mode =====
  
-**Enable the CF bootstrap mode and reset.**+**Enable the CF bootstrap mode and reset.  It is not necessary to add line transmission delay to the serial port communication in the following.**
 ==== Install CP/M2.2 ==== ==== Install CP/M2.2 ====
  
-**Load cpm22all.hex before issuing '​c2'​ command.**+**Load ​{{:​builderpages:​plasmo:​tinyz280:​cpm22all_hex_loadfile.zip|cpm22all.hex}}  ​before issuing '​c2'​ command.**
  
 //TinyZZ Monitor v0.99 6/9/18// //TinyZZ Monitor v0.99 6/9/18//
Line 55: Line 55:
 ==== Install CP/M 3 ==== ==== Install CP/M 3 ====
  
-**Load cpmldr.hex before issuing '​c3'​ command.**+**Load ​{{:​builderpages:​plasmo:​tinyz280:​cpmldr_hex.zip|cpmldr.hex}}  ​before issuing '​c3'​ command.**
  
 //>​…………………………………………………………………………………………………………X//​ //>​…………………………………………………………………………………………………………X//​
Line 66: Line 66:
 2–CP/​M2.2,​\\ 2–CP/​M2.2,​\\
 3–CP/M3: //**3**// press Return to execute command// 3–CP/M3: //**3**// press Return to execute command//
-==== Install CP/M22 distribution files ====+====  Install ​ CP/M22 distribution ​  ​files  ====
  
 **Clear drives A/B/C/D before loading CPM distribution files** **Clear drives A/B/C/D before loading CPM distribution files**
Line 98: Line 98:
 E – RAM drive: //**D**// press Return to execute command// E – RAM drive: //**D**// press Return to execute command//
  
-**load cpm22dri.hex,​ this is the cpm22 distribution files.**+**load ​{{:​builderpages:​plasmo:​tinyz280:​cpm22dri.zip|cpm22dri.hex}}, this is the cpm22 distribution files.**
  
 //>​E………………………………………………………………//​**long response, truncated**//​……………………………………………..X//​ //>​E………………………………………………………………//​**long response, truncated**//​……………………………………………..X//​
Line 143: Line 143:
 ==== Install CP/M 3 distribution files ==== ==== Install CP/M 3 distribution files ====
  
-**Load the CPM3 distribution files.\\ +**Load the CPM3 distribution files, {{:​builderpages:​plasmo:​tinyz280:​cpm3dstr.zip|CPM3DSTR.HEX}} \\ 
-It is a big file, taking ​minutes and 40 seconds to load.**+It is a big file, taking ​minutes and 20 seconds to load at 115200 buad.**
  
 //​e>​TinyZZ Monitor v0.99 6/9/18// //​e>​TinyZZ Monitor v0.99 6/9/18//
builderpages/plasmo/z280rc/new_cfdisk.txt · Last modified: 2018/06/10 13:13 by plasmo
Driven by DokuWiki Recent changes RSS feed Valid CSS Valid XHTML 1.0